How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
Just how do you feel in regards to Installing A Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old bathtub is readily obtainable, the job can move easily; if you have to open up a wall to get rid of the old tub and position the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the task and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is better to think about employing one prior to you start. Possibilities are you might need a specialist plumber to make tube links.
This short article will certainly help you set up a brand-new tub in your washroom if you have currently bought a new bathtub and do not require to alter the setup of your previous water pipes.
Your devices and also material list ought to make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of getting rid of the existing faucets can be fairly bothersome due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location between the tap as well as the sink. Protect the faucet in position with the supplier given backnut. As soon as the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Tub
Utilizing both wooden boards under its feet, put the tub in the needed position. The wood boards are useful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to make certain that the tub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub until the level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water system as well as check all joints and new pipework for leakages and also tighten them if needed. Fill the bathtub as well as likewise check the overflow outlet and also the typical outlet for leakages.
Lastly, repair the bath paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub needs to wait up until the bathtub has been used at the very least once as this will certainly settle it into its final placement.
Getting ready for the Installment
First of all, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to now be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, resulting in issues with moisture and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the tub with water before sealing, to permit the activity experienced when the bathtub is in usage. The sealer can break fairly very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the market. It is recommended to fit the floor tiles making use of water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that piece of writing on How to Install a Bathtub Yourself while doing a lookup on the web. Are you aware of another individual who is interested by How to Install a Bathtub? Why not promote it. Thanks for your time. Come back soon.
Get Offer
Report this page